Manual Alarma Bunker Vip 500 Gram
• 15P0059B3 • DCREG2 DCREG4 USER MANUAL 15/07/08 R.06 SOFTWARE VERSION D5.00 • This manual is an integral and essential part of the product. Carefully read the instructions contained herein as they provide important hints for use and maintenance safety. • This device shall be used only for the purposes it is aimed at. Isuzu Npr 4hl1 4.8l Diesel Engine With Manual Transmission Jdm Isuzu Npr 4hl1. Keithley 2430-c Sourcemeter - $7,495.00. Day Date Gold Band For Rolex Aprox. 61 Grams For Rolex 20 M.m.w. Check Picture. Vince Lombardi Masterpiece - $6,999.99. Underground Bunker Vip Fall Out Shelter Bug Out With Data Center Acreage Ect. Patent For Sale.
• ® 500 ESP Installation Guide ® © 1999 Directed Electronics, Inc. Vista, CA N439 12-99. • table of contents What Is Included. 3 Shock Sensor Harness, 4-Pin Connector.23 Installation Points to Remember.4 Internal Programming Jumper. • what is included The control module (see diagram) Two 476 Series four-button remote transmitters A plug-in status LED A plug-in Valet ® /Program switch A plug-in Stinger® shock sensor A Revenger ® Soft Chirp ® siren PC Program/Data Port Blue 2-Pin Valet ®.
• installation points to remember This product represents many years of research and development. It is very sophisticated and should be installed by experienced security installers only. Please do not attempt installation of this product without reading this guide. The system has been designed to provide the ultimate in security, coupled with limitless convenience and expansion options.
• deciding on component locations locations for the siren Some things to remember about mounting the siren: Keep it away from heat sources, such as radiators, exhaust manifolds, turbochargers, and heat shields. Mount it where a thief cannot easily disconnect it, whether the hood is open or shut. Both the siren and its wires should be difficult to find. • The higher the control module is in the vehicle, the better the transmitter range will be. If you put the control module under a seat or inside a metal dashboard, range will suffer, and you may wish to add a DEI ®.
• locations for valet/program switch IMPORTANT! When the vehicle is delivered, please show the user where this switch is located and how to disarm the system with it. Ensure that the location you pick for the switch has sufficient clearance to the rear.
The switch should be well hidden. • locations for the starter kill relay If starter kill relay or its connections are immediately visible upon removal of the under-dash panel, they can easily be bypassed. Always make the relay and its connections difficult to discern from the factory wiring! Exposed yellow butt connectors do not look like factory parts, and will not fool anyone!
For this reason, routing the starter kill wires away from the steering column is recommended. 3dsimed keygen idm 2017. • How to find (+)12V ignition with your multimeter: 1. Set to DCV or DC voltage (12V or 20V is fine).
Attach the (-) probe of the meter to chassis ground. Probe the wire you suspect of being the ignition wire. The steering column harness or ignition switch harness is an excellent place to find this wire. • Once you have determined the wire color, the easiest place to connect to the wire is often at the kick panel, at the windshield pillar, or in the running board. When an easy location is not available, running a wire to the dome- light itself is often the best solution. • primary harness (H1), 12-pin connector ______ ORANGE (-) 500 mA ARMED OUTPUT H1/1 ______ WHITE (+)/(-) SELECTABLE LIGHT FLASH OUTPUT H1/2 ______ WHITE/BLUE (-) 200 mA CHANNEL 3 PROGRAMMABLE OUTPUT H1/3 ______ BLACK/WHITE (-) 200 mA DOMELIGHT SUPERVISION OUTPUT H1/4 ______ GREEN (-) DOOR TRIGGER INPUT, ZONE 3. Never interrupt any wire other than the starter wire.